12头222 dtex/18 f聚酰胺66纺丝技术Technology for 12 End 222 dtex/18 f Polyamide 66 FDY
张明成,曹新荣
ZHANG Ming-cheng,CAO Xin-rong
摘要(Abstract)：
以生产12头222 dtex/18 f聚酰胺66为例介绍了纺丝工艺条件:采用双螺纹螺杆挤压机,切片可以均匀熔融,机头压力波动小;采用分体式纺丝箱体,容易煅烧,拆装工程量小;采用三杆双侧固定架上油装置,上油均匀,纤维品质高;采用三组热辊两级牵伸,纤维强力高、能耗小;采用全并联热媒供热系统,热媒流速快,系统温差小;采用2.2 m高的侧吹风窗,门上部为百叶窗透气结构,下部为玻璃密封结构,丝束无弯曲、摆动、相互缠绕和粘连现象;选择合理的喷丝板微孔,纤维可纺性较好。
The spinning process conditions were introduced in 12 end 222 dtex/18 f polyamide 66. Whendouble screw extruder was used, the chip was melted evenly and the pressure surge was low. It was easy tocalcinate with the split type spin beam, and the amount of unpacking was small. The three-pole double-side fixed oil installation was used, the upper oil was uniform, the fiber quality was high. Three sets of hotroller two-level drafting was used, fiber strength was high, energy consumption was small. The fully parallelheat medium heating system was adopted, the velocity of the heat medium was fast and the system tempera-ture difference was small. The upper part of the door was window-shades structure, the under part was theglass sealing structure, and the fibers were not bent, swing, intertwine and adhesion. The reasonable spinner-et microhole was chosen, the spinnability was better.
关键词(KeyWords)：
聚酰胺66;12头纺;工艺
polyamide 66;12 end;process conditions
基金项目(Foundation):
作者(Author):
张明成,曹新荣
ZHANG Ming-cheng,CAO Xin-rong
DOI: 10.16090/j.cnki.hcxw.2018.09.001
参考文献(References)：
- [1]张建一,侯建国,王秀艳.220 dtex/18 f PA66 FDY生产工艺简介[J].合成纤维工业,2005,28(5):54-55.
- [2]张明成.锦纶66细旦工业丝高速纺设备的研制及相关工艺[J].合成纤维,2015,44(12):10-13.
- [3]陈立军,张明成.一种用于纺丝的热媒循环供热系统:CN20317615.1[P].2010.
- [4]康伟峰,牛国旗.环境条件对尼龙66工业丝可纺性的影响[J].合成纤维工业,2004,27(3):46-48.
- [5]张明成,孔维嘉.锦纶6 FDY分纤母丝高速纺丝技术创新[J].聚酯工业,2017,30(3):19-22.
- [6]张明成,姜军,陈立军,等.将每根丝束分解开的分丝部件和上油装置:CN10144397.7[P].2015.
- [7]张明成,陈立军,姜军.拉丝装置及涤纶、锦纶6通用型分纤母丝纺丝系统:CN105063777A[P].2015.
- [8]MILLER C.Predicting non-newtonian flow behavior in ducts of unusual cross section[J].Industrial&Engineering Chemistry Fundamentals,2002,11(4):524-528.
- [9]郑淑昀,陈妍丽,郝丽君.高性能尼龙66缝纫线丝生产工艺研究[J].中国科技信息,2005,2(19A):32-32.