陈志军,庞蓉蓉,曾鸣,段秋飞
CHEN Zhi-jun,PANG Rong-rong,ZENG Ming,DUAN Qiu-fei

• 1:武汉纺织大学纺织科学与工程学院
• 2:天津工业大学纺织科学与工程学院
• 3:东莞超盈纺织有限公司

摘要(Abstract)：

用熔喷非织造布设备制备聚乳酸(PLA)熔喷非织造布,并以此作为接收基布,将PLA静电纺纤维喷覆在上面,制得PLA静电纺/熔喷复合纤维膜。对比分析了PLA熔喷非织造布和静电纺/熔喷复合纤维膜的表观形貌、纤维直径及直径分布,测试了孔径大小及其分布、过滤效率、透气性和力学性能,得出如下结论:PLA静电纺纤维直径分布主要在2～2.40μm,熔喷纤维直径分布主要在5～6μm,两种纤维叠合在一起,直径等级区分清晰,结构梯度明显;PLA熔喷非织造布的孔径主要分布在10μm左右,PLA静电纺/熔喷复合纤维膜的孔径分布在8μm左右,PLA熔喷非织造布表面喷覆PLA静电纺纤维后,透气率下降,断裂强力增加了75.4%,断裂伸长率减小。
Polylactic acid(PLA) meltblown nonwoven fabric was prepared as a receiving base fabric, and PLA electrospinning fibers were sprayed on a PLA meltblown nonwoven fabric to obtain a PLA electrospinning/meltblown composite fiber membrane. The apparent morphology of PLA meltblown nonwoven and electrospinning/meltblown composite fiber membrane were analyzed. The fiber diameter, diameter distribution, pore size and distribution, filtration efficiency, air permeability and mechanics performance were tested. The conclusions were as follows: the diameter of PLA electrospinning fiber was mainly distributed in 2～2.40 μm, the diameter of the meltblown fiber was mainly distributed in 5～6 μm, the two kind of fibers were stacked together, the diameter grade was clear, and the structural gradient was obvious. The pore size of PLA meltblown nonwoven fabric was mainly distributed at about 10 μm. The pore size distribution of PLA electrospinning/meltblown composite fiber membrane was about 8 μm. After the surface sprayed PLA electrospinning fiber, the air permeability of PLA meltblown nonwoven decreased, the breaking strength increased by 75.4%, the elongation at break decreased.

关键词(KeyWords)： 聚乳酸;熔喷非织造布;静电纺丝;复合纤维膜
polylactic acid;meltblown monwoven;electrospinning;composite fiber membrane

Abstract:

Keywords:

基金项目(Foundation):

作者(Author): 陈志军,庞蓉蓉,曾鸣,段秋飞
CHEN Zhi-jun,PANG Rong-rong,ZENG Ming,DUAN Qiu-fei

DOI: 10.16090/j.cnki.hcxw.2021.05.007

参考文献(References)：

• [1]何宏升,邓南平,范兰兰,等.熔喷非织造技术的研究及应用进展[J].纺织导报, 2016(S1):71-80.
• [2]马贵平,方大为,刘洋,等.电纺丝制备纳米纤维及其应用[J].材料科学与工程学报, 2012, 30(2):312-323.
• [3] GAO H C, YANG Y Q, AKAMPUMUZA O, et al. A low filtration resistance three-dimensional composite membrane fabricated via free surface electrospinning for effective PM2.5capture[J]. Environmental Science Nano, 2017(4):864-875.
• [4]吴红艳,陈振宏,吕悦慈.静电纺PBS/熔喷复合滤材的制备及性能表征[J].纺织导报, 2017(9):70-73.
• [5]刘雷艮,沈忠安,洪剑寒.静电纺高效防尘复合滤料的制备及其性能[J].纺织学报, 2015, 36(7):12-16.
• [6]倪冰选,杨欣卉,张鹏.静电纺纳米纤维复合梯度型空气过滤材料的研究进展[J].合成纤维工业, 2017, 40(6):47-52.
• [7]康卫民,程博闻,庄旭品,等.静电纺纳米级纤维复合纤维膜及其过滤性能[J].纺织学报, 2006, 27(10):6-8.
• [8] YAO Q Q, COSME J G L, XU T, et al. Three dimensional electrospun PCL/PLA blend nanofibrous scaffolds with significantly improved stem cells osteogenic differentiation and cranial bone formation[J]. Biomaterials, 2017, 115:115-127.
• [9] XU T, MISZUK J M, ZHAO Y, et al. Electrospinning polycaprolactone3D nanofibrous scaffold with interconnected and hierarchically structured pores for bone tissue engineering[J]. Advanced Healthcare Materials,2015, 4(15):2238-2246.
• [10]刘亚.熔喷/静电纺复合法聚乳酸非织造布的制备及过滤性能研究[D].天津:天津大学, 2009.
• [11]姚春梅,黄锋林,魏取福,等.静电纺聚乳酸纳米纤维复合滤料的过滤性能研究[J].化工新型材料, 2012, 40(4):122-124.