杨新革,于俊荣,郭清,陈蕾,诸静,胡祖明
YANG Xin-ge1,YU Jun-rong2*,GUO Qing2,CHEN Lei2,ZHU Jing2,HU Zu-ming2 (1.School of Chemistry

• 1:临沂大学化学与资源环境学院
• 2:东华大学纤维材料改性国家重点实验室

摘要(Abstract)：

采用双螺杆挤出纺丝工艺,探讨了高原液浓度、高相对分子质量聚乙烯(HMWPE)的溶解性及可纺性,研究了双螺杆转速及温度对所得HMWPE冻胶纤维黏均分子量的影响。结果表明:双螺杆挤出机可以完成适当浓度HMWPE的溶胀、溶解和挤出纺丝,原液PE质量分数为20%～40%时制得的冻胶纤维具有一定高倍拉伸性能;随螺杆转速的增加,制得的HMWPE纤维黏均分子量稍有提高或变化不大,至一定螺杆转速后又开始降低;HMWPE纤维的黏均分子量随纺丝螺杆输送段温度的提高而变高,至一定温度后又大大降低;HMWPE原液PE质量分数为20%和30%时,最佳螺杆输送段温度为240℃,而原液PE质量分数为40%时,最佳螺杆输送段温度为250℃。
By means of twin-screw extruding and gel spinning technology,the dissolvability and spinnability of high concentration and high molecular weight polyethylene(HMWPE) were discussed.The effect of twin-screw rotating rate and spinning temperature on the average molecular weight of HMWPE gel fibers were investigated.The results showed that twin-screw extruder could act as the swelling,dissolving and extruding device of HMWPE solution,the HMWPE gel fiber possessed high drawability when HMWPE concentration was from 20 % to 40 %.With the increasing of twin-screw rotating rate,the viscosity average molecular weight of HMWPE increased or remained unchanged,and then it decreased when certain rotating rate had been reached.The viscosity average molecular weight of HMWPE increased with increasing of spinning temperature and then distinctly decreased.The optimum spinning temperature for both 20 % and 30 % HMWPE solution were 240 ℃,spinning temperature became 250 ℃ when HMWPE concentration was 40 %.

关键词(KeyWords)： 高相对分子质量聚乙烯;双螺杆挤出机;冻胶纺丝;黏均分子量
high molecular weight polyethylene,twin-screw extruder,gel spinning,viscosity average molecular weight

Abstract:

Keywords:

基金项目(Foundation):

作者(Author): 杨新革,于俊荣,郭清,陈蕾,诸静,胡祖明
YANG Xin-ge1,YU Jun-rong2*,GUO Qing2,CHEN Lei2,ZHU Jing2,HU Zu-ming2 (1.School of Chemistry

DOI: 10.16090/j.cnki.hcxw.2011.06.015

参考文献(References)：

• [1]于俊荣.聚乙烯纤维的纺丝方法及高强化研究进展[J].产业用纺织品,2000,18(4):17-21.
• [2]河野安男,伊藤雄一,八木和雄.高分子量聚乙烯模塑成型的分子取向制品及其制备方法:中国,CN90107707.0[P].1990-09-11.
• [3]W G Perkins,N J Capiati,R S Porter.The effect of molecular weighton the physical and mechanical properties of ultra-drawn high densitypolyethylene[J].Polym Eng Sci,1976,16(3):200-203.
• [4]肖长发,安树林,贾广霞,等.超高分子量聚乙烯溶液的降解与抗降解[J].塑料工业,1994,22(3):31-33.
• [5]铉晓群,潘婉莲,于俊荣,等.抗氧剂在UHMWPE溶解过程中的作用[J].合成纤维工业,2006,29(2):37-39.
• [6]丁永红,承民联,林明德.双螺杆挤出机在聚烯烃分子量及其分布控制中的应用[J].江苏石油化工学院学报,1998,10(1):58-60.
• [7]于俊荣,胡祖明,刘兆峰.超高相对分子质量聚乙烯溶液的制备[J].中国纺织大学学报,2000,26(6):90-93.
• [8]P Smith,P J Lemstra,H C Booij.Ultradrawing of high-molecular-weight polyethylene cast from solution.Ⅱ.Influence of initial polymerconcentration[J].J Polym Sci:Polym Phys Ed,1981,19(5):877-888.