汪晓允,赵宏飞,李明明,胡世林,苏海霞,刘伟
WANG Xiao-yun,ZHAO Hong-fei,LI Ming-ming,HU Shi-lin,SU Hai-xia,LIU Wei

• 1:江苏恒神股份有限公司

摘要(Abstract)：

采用树脂转移模塑成型(RTM)工艺，研究多墙结构副翼低成本整体成型的可行性。采用数值模拟技术对多墙结构副翼的树脂流动过程进行了模拟计算，根据模拟结果选择合理的注射方式和工艺参数，同时采用碳纤维编织套管成型副翼墙，以进一步降低制造成本。对所选方案进行了工艺试验验证，并对结构件进行了质量检测。结果表明：碳纤维编织套管的应用大大提高了预制体的制备效率，节省人工约60%；理论充模时间和试验充模时间基本一致；结构件表观质量良好，厚度分布均匀，内部无缺陷，验证了所选模拟方案合理有效，整体成型方案切实可行。研究结果为低成本制造高性能复合材料多墙结构件提供了参考。
The resin transfer molding(RTM) process was used to study the feasibility of low-cost integral molding on the multi-wall structure aileron. The resin flow process of multi-wall structure aileron was simulated by numerical simulation technology. According to the simulation results, a reasonable injection method and technological parameters were selected. At the same time, fiber braided tubes were used to form aileron walls to further reduce the manufacturing cost. The process test of the selected scheme was verified, and the quality of the structural parts was tested. The results show that the application of carbon fiber braided tubes greatly improves the preparation efficiency of the preform and saves about 60% of labor. The theoretical filling time is consistent with the experimental filling time basically. The structural parts have good apparent quality, uniform thickness distribution, and no internal defects, which verifies that the simulation scheme is effective, and the integral forming scheme is feasible. The research results provide a reference for the low-cost fabrication of high-performance composite multi-wall structures.

关键词(KeyWords)： RTM;整体成型;多墙结构副翼;数值模拟;碳纤维编织套管
RTM;integralforming;multi-wallstructureaileron;numericalsimulation;carbonfiberbraidedtube

Abstract:

Keywords:

基金项目(Foundation):

作者(Author): 汪晓允,赵宏飞,李明明,胡世林,苏海霞,刘伟
WANG Xiao-yun,ZHAO Hong-fei,LI Ming-ming,HU Shi-lin,SU Hai-xia,LIU Wei

DOI: 10.16090/j.cnki.hcxw.2023.05.006

参考文献(References)：

• [1]刘善国.国外飞机先进复合材料技术[J].航空制造技术, 2014(19):26-31.
• [2]赵云峰,孙宏杰,李仲平.航天先进树脂基复合材料制造技术及其应用[J].武宇航材料工艺, 2016, 46(4):1-7.
• [3]郭俊刚,张新娟,田亦瑶,等.复合材料液体成型技术在飞机上的应用及发展[J].宇航材料工艺, 2022, 52(2):85-91.
• [4]赵龙,黄峰,刘强,等.多腔结构预成型体及RTM树脂流道设计技术研究[J].航空制造技术, 2008(15):74-77.
• [5]张默,李炜. VARTM工艺中增强体的渗透率测定[J].玻璃钢/复合材料, 2011, 221(6):54-56.
• [6] DAI F H, DU S Y, ZHANG B M, et al. A new method to track resin flow front in mold filling simulation of RTM process[J]. Journal of Materials Science&Technology, 2004, 20(3):335-340.
• [7] PARNASR S, PHELAN F R. The effect of heterogeneous porous media on mold filling in resin transfer molding[C]. SAMPE Quarterly, 1991(1):53-60.
• [8]江顺亮. RTM加工工艺充模过程的计算机模拟[J].复合材料学报,2002, 19(2):13-17.
• [9]刘松良,康亮,周开锋,等.采用RTM技术制造复合材料异型正弦波形梁[J].飞机设计, 2018, 38(4):71-75.